Sealing a Mixed Fibreglass/Paving Balcony Floor and Fitting a New Composite Deck
Balcony waterproofing We have an outdoor balcony c. 8m x 3m of which 2/3 has a fibreglass floor (c.2005) and 1/3 concrete paving slabs (original 1995). It’s covered with 120mm pressure treated decking timber mounted on pressure treated timber battens sitting on narrow pieces of tiles. Rainwater downpipes drain onto the floor and away under the battens and tiles. Some of the battens are rotten and need replacing. Part of the ceiling in the room below the join between the fibreglass and paving floor is showing some signs of damp.
Q1: What is the best way to seal and cover the floor containing both the fibreglass and the slabs? Q2: Would the flooring be able to support a replacement composite deck?
==========================
Answer:-
Thanks for the detailed description — this is a very common situation with older balconies that have been extended or patched over the years, and the symptoms you’re describing (rotten battens, damp ceiling below the join) point to a fairly clear underlying problem.
What’s Causing Balcony Waterproofing Failure at the Join
The joint between the fibreglass area and the paving slab area is almost certainly the weak point. Fibreglass (GRP) and traditional paving are two completely different waterproofing systems, and unless they were properly detailed together with a continuous upstand or overlap at the time of installation, that junction will always be a route for water to track through. Add to that:
- Downpipes discharging directly onto the deck surface, which concentrates a lot of water exactly where the timber battens and packers sit
- Battens resting on small tile off-cuts, which don’t allow for even drainage or ventilation underneath
- 20+ years of movement, thermal cycling, and UV degradation on the original 1995 paving and the 2005 fibreglass
This combination is a textbook recipe for water finding its way to the join, sitting there, and eventually working through to the ceiling below — which matches exactly what you’re seeing.
Q1: Sealing and covering a floor with two different substrates
You have two realistic options:
Option A – Overlay with a single, continuous waterproofing membrane
The most robust long-term fix is to strip back to the structural deck (or at least fully expose the fibreglass and slabs), remove the old paving, and install one continuous liquid-applied or GRP waterproofing membrane across the entire balcony — fibreglass area and former paving area alike. This gets rid of the problematic junction entirely, because you end up with a single seamless waterproof layer rather than two systems meeting in the middle.
Key details we’d want to get right:
- A minimum 150mm upstand at all walls and door thresholds, properly detailed with cover flashing
- Correct falls (minimum 1:80, ideally 1:60) directing water to defined outlets — not just “away under the battens”
- Outlets and downpipe discharge points re-engineered so rainwater goes into a proper drain or gully rather than sheeting across the deck surface
- A ventilated support system for anything sitting on top (see below), rather than timber battens on loose tile packers
Option B – Overlay only, without removing the paving
It’s sometimes possible to bridge over sound paving with a new membrane rather than removing it, provided the slabs are stable, well-bonded, and not causing a step or trip hazard at the fibreglass junction. This is cheaper and less disruptive, but it’s a compromise: the membrane is relying on a stable substrate underneath, and if the paving was ever bedded on sand or has any movement, you risk the same cracking-at-the-join problem re-appearing over time.
Given that you already have a confirmed damp issue at that exact junction, we’d generally recommend Option A. Patching or overlaying without addressing the root cause tends to buy a few years at best before the same symptoms return.
Q2: Can the floor take a replacement composite deck?
In principle, yes — but not directly on the current setup, and not without some changes:
- Support system first. Timber battens resting on odd tile off-cuts is exactly the kind of detail that traps water and rots timber, which is what’s already happened. For a new composite deck, we’d recommend adjustable plastic or composite deck support pedestals (paver/deck supports) rather than timber-on-tile packers. These are height-adjustable, sit on the waterproof membrane without penetrating it, and allow water to drain and air to circulate freely underneath — removing the rot risk almost entirely.
- Weight is rarely the limiting factor. Composite decking is generally similar in weight to, or only modestly heavier than, timber decking of the same dimensions, and a structure that has coped with 120mm pressure-treated timber decking, battens, and 1990s paving slabs for 20+ years is very unlikely to be overloaded by a composite deck on pedestals. The real question isn’t “can it take the weight” — it’s “is the waterproofing underneath sound,” because that’s what determines whether the deck will still be doing its job in 10 years’ time.
- Get the membrane and falls right before decking goes down. Composite deck boards don’t waterproof anything themselves — they sit above the weatherproofing layer, not as part of it. If you deck straight over the existing mixed floor without addressing the membrane and the junction, you’ll simply be hiding the same problem under a new surface while the damp continues underneath.
Our 5-Step Balcony Waterproofing Approach
- Have the balcony structure and the damp-affected ceiling area inspected to confirm there’s no rot or structural damage that needs addressing first
- Strip back to expose the full floor, remove ageing paving and any failed fibreglass sections
- Install a single continuous waterproofing membrane across the whole balcony with correctly falling drainage and properly detailed upstands
- Re-route or box the downpipe discharge so it doesn’t run directly across the deck area
- Fit height-adjustable deck support pedestals on top of the membrane
- Lay the new composite decking on the pedestal system
This gives you one consistent waterproof layer (no more fibreglass-to-paving junction to fail), solves the rot problem by getting the deck support off the membrane and ventilated, and gives the new composite deck a stable, long-lasting base.
==========================
Contact Us :
(0)20 3987 4923
Mob: 07404960364
info@vrltd.uk
566 Chiswick High Street, W4 5YA, London

